Raspberry base install - Revision history

Jca at 09:38, 22 October 2023

2023-10-22T09:38:27Z

← Older revision		Revision as of 11:38, 22 October 2023
Line 11:		Line 11:
	rpi-imager		rpi-imager

	First configure settings: click the gear icon, and set:		'''First''' configure settings: click the gear icon, and set:

	* enable ssh, hostname, English language, Danish keyboard, possibly SSID, time zone, username (local) and password (remember to spell the password correctly).		* enable ssh, hostname, English language, Danish keyboard, possibly SSID, time zone, username (local) and password (remember to spell the password correctly).

Jca: /* Start Raspberry */

2023-08-12T14:00:34Z

Start Raspberry

← Older revision		Revision as of 16:00, 12 August 2023
Line 52:		Line 52:
	In this case, the IP4 (inet) is 10.197.217.175.		In this case, the IP4 (inet) is 10.197.217.175.

	If you don't get an IP, the wifi may not be set correctly (see the ~~wifi~~ setup).		If you don't get an IP, the wifi may not be set correctly (see the [[Network setup]]).

Jca at 13:59, 12 August 2023

2023-08-12T13:59:50Z

← Older revision		Revision as of 15:59, 12 August 2023
Line 1:		Line 1:
			Back to [[robobot B]]


	== Installation from blank SD-flash ==		== Installation from blank SD-flash ==

Jca: /* Start Raspberry */

2023-08-12T13:59:19Z

Start Raspberry

← Older revision		Revision as of 15:59, 12 August 2023
Line 47:		Line 47:


	In this case, the IP4 is 10.197.217.175.		In this case, the IP4 (inet) is 10.197.217.175.

	If you don't get an IP, the wifi may not be set correctly.		If you don't get an IP, the wifi may not be set correctly (see the wifi setup).

Jca: Created page with "== Installation from blank SD-flash == === Install Raspberry === Use Raspberry pi imager (download from https://www.raspberrypi.com/software/) rpi-imager First configure..."

2023-08-12T13:57:36Z

Created page with "== Installation from blank SD-flash == === Install Raspberry === Use Raspberry pi imager (download from https://www.raspberrypi.com/software/) rpi-imager First configure..."

New page

== Installation from blank SD-flash ==

=== Install Raspberry ===

Use Raspberry pi imager
(download from https://www.raspberrypi.com/software/)

rpi-imager

First configure settings: click the gear icon, and set:

* enable ssh, hostname, English language, Danish keyboard, possibly SSID, time zone, username (local) and password (remember to spell the password correctly).

then

'''Select operating system''' 'Raspberry Pi OS lite' and '''storage''', an empty SD-flash of at least 16GB, then '''write'''.

When finished, mount the SD into the Raspberry

=== Start Raspberry ===

If everything is configured as above, then you just need to figure out the IP.
On a Linux computer, you can find the Raspberry IP address using (if on the same local net):

sudo apt install net-tools nmap
nmap -sP 192.168.2.0/24

else

You need a screen and keyboard.

Log on to the Raspberry Pi

$ ifconfig
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
...
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
...
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.197.217.175 netmask 255.255.252.0 broadcast 10.197.219.255
inet6 fe80::f620:b431:69cc:44f4 prefixlen 64 scopeid 0x20<link>
ether dc:a6:32:f4:0e:a4 txqueuelen 1000 (Ethernet)
RX packets 486 bytes 41505 (40.5 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 421 bytes 43403 (42.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

In this case, the IP4 is 10.197.217.175.

If you don't get an IP, the wifi may not be set correctly.