|
|
| (2 intermediate revisions by the same user not shown) |
| Line 3: |
Line 3: |
| === 2012 version with Xubuntu 12.04=== | | === 2012 version with Xubuntu 12.04=== |
|
| |
|
| NB! not finished yet, but there is clone scrips (from image to new bootable disk) on smr24 in room 011:
| | ====Clone image to (new) disk==== |
| | |
| | Make a new bootable disk from existing image: |
| | |
| | Use '''clone-xubuntu''' and '''clone-databar''' on smr24 (room 011) as root in /root, where available images are in the ''images'' subdirectory. |
|
| |
|
| ====Make new boot image==== | | ====Make new boot image==== |
| Line 20: |
Line 24: |
| umount disk | | umount disk |
|
| |
|
| ====Clone image to (new) disk====
| |
|
| |
| Make a new bootable disk from existing image:
| |
|
| |
| Use '''clone-xubuntu''' and '''clone-databar''' on smr24 as root in /root, where available images are in the ''images'' subdirectory.
| |
|
| |
| === Old 2011 version ===
| |
|
| |
| In order to support both VIA Nehemiah and Intel Atom based platforms two kernels must be included in the smr flash image.
| |
| * 2.6.32.20-rtai supports multicore systems and hyperthreading
| |
| * 2.6.32.20-rtai-up supports single core systems and is optimized to the Via processors
| |
|
| |
| A new clone script called <tt>multiclone</tt> must be used when this image is flashed. The script is in the root folder of rt15.
| |
|
| |
| ==== Flash cloning procedure on rt15 ====
| |
|
| |
| Via processors using CF-card flash-disks:
| |
| * Log in as root (If you don't know the password abort immediately)
| |
| * Insert the CF-card in the reader in the front of rt15.
| |
| * Check the device name the card is given: <tt>tail /var/log/messages</tt>. Usually it is <tt>/dev/sdb</tt>.
| |
| * Go to the image folder: <tt>cd image</tt>
| |
| * Locate the image you would like to burn (usually the newest one), for instance: <tt>flash-2011-01-01.tgz</tt>
| |
| * Start the procedure:
| |
| root@rt15:~# ../multiclone flash-2011-01-01.tgz /dev/sdb via
| |
|
| |
| ''NB: Note the two dots in front of multiclone''
| |
|
| |
| The procedure for cloning Intel Atom images is the same, except <tt>atom</tt> must be stated last in stead of <tt>via</tt> as in:
| |
| root@rt15:~# ../multiclone flash-2011-01-01.tgz /dev/sdb atom
| |
|
| |
| === Old description ===
| |
|
| |
| Some of the SMR's now have solid-state flash memory disks, instead of the laptop, 2.5" disks used on older models.
| |
|
| |
| This wiki page contains some notes describing how to write a bootable flash disk image (Slackware Linux) to a memory card. It assumes a Linux PC with USB flash card reader/writer, available as /dev/sda.
| |
|
| |
| The commands below is implemented in this script Clone script. Usage:
| |
|
| |
| clone <from_file.tar.gz> <to device>
| |
| <to device> can be both the USB bus (/dev/sdx) or a IDE device (/dev/hdx)
| |
|
| |
| The script will place a file .cloned-at on the Flash Disk with time information for the cloning.
| |
|
| |
| If you put the Flash Disk on the IDE bus and the computer will not boot (LILO - Timestamp mismatch) then the MBR on the Flash Disk must be erased as follows:
| |
|
| |
| dd if=/dev/zero of=/dev/hdx bs=1 count=512
| |
| Writing an image
| |
|
| |
| Format the disk, with one large Linux partition:
| |
|
| |
| sfdisk -L /dev/sda <<EOF
| |
| ,,L,*
| |
| EOF
| |
| Create a filesystem:
| |
|
| |
| mke2fs /dev/sda1 -L /
| |
| Mount the new, empty partition:
| |
|
| |
| mkdir -p /tmp/u
| |
| mount /dev/sda1 /tmp/u
| |
| Write a previously created image from flash.tar.gz
| |
|
| |
| zcat flash.tar.gz |
| |
| tar --extract --file - --directory /tmp/u --preserve-permissions
| |
| Create a patched lilo.conf, so that we can run LILO with the flash card mounted via USB. (This won't be necessary if the image written above already contains such a file.)
| |
|
| |
| patch -o /tmp/u/etc/lilo_usb.conf /tmp/u/etc/lilo.conf <<EOF
| |
| *** /tmp/u/etc/lilo.conf Tue Nov 4 21:34:44 2003
| |
| --- lilo_usb.conf Thu Dec 11 11:50:55 2003
| |
| ***************
| |
| *** 4,6 ****
| |
| # Start LILO global section
| |
| ! boot = /dev/hda
| |
| message = /boot/boot_message.txt
| |
| --- 4,7 ----
| |
| # Start LILO global section
| |
| ! boot = /dev/sda
| |
| ! disk = /dev/sda bios=0x80
| |
| message = /boot/boot_message.txt
| |
| EOF
| |
| Run LILO:
| |
|
| |
| chroot /tmp/u lilo -v -C /etc/lilo_usb.conf
| |
| All done:
| |
|
| |
| umount /dev/sda1
| |
| eject /dev/sda
| |
| Reading an image
| |
|
| |
| Mount as above:
| |
|
| |
| mkdir -p /tmp/u
| |
| mount /dev/sda1 /tmp/u
| |
| Read the partition:
| |
|
| |
| tar --create --file - --directory /tmp/u --one-file-system --exclude lost+found . |
| |
| gzip > flash.tar.gz
| |
| or
| |
|
| |
|
| tar -zcf - -C /tmp/u --one-file-system --exclude lost+found . > flash.tar.gz
| | ==Old description== |
| All done:
| |
|
| |
|
| umount /dev/sda1
| | [[old disk cloning procedure]] |
| eject /dev/sda
| |
