|
|
| (7 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| This is some suggestions for changed settings for Robobot.
| | Moved to [[regbot settings]] |
| | |
| == Robot configuration==
| |
| | |
| Metric setup
| |
| | |
| The distance between driving wheels are different from a Regbot.
| |
| | |
| [[File:robobot_robot_settings.png]] | |
| | |
| == Control issues ==
| |
| | |
| Some examples of control settings.
| |
| | |
| ===Edge control===
| |
| | |
| For higher speed in the range 0.7-0.9 m/s the following control settings could be used.
| |
| | |
| [[File:line_edge_control.png]]
| |
| | |
| The control uses a Lag-controller to decrease the static gain by a factor 5 (a pole with a time constant of 1.5 sec and a zero with a time constant of 0.3 seconds). This means that the high frequency gain is Kp*0.3/1.5 = 0.06.
| |
| | |
| The gain is further scaled by the speed (from firmware version 604), so that the gain is reduced to half at 0.5m/s, but the filter times are maintained. This is probably a bad solution, as the response probably is more distance driven than time driven.
| |
| | |
| | |
| A test script to could be:
| |
| | |
| thread=1
| |
| vel=0.01, acc=5.0, log=50.0: time=0.2
| |
| vel=0.9, edger=1, white=0: dist=10.0, xb=20
| |
| vel=0,event=7 : xb<10
| |
| :vel< 0.1
| |
| vel=-0.3,tr=0.1:turn=60
| |
| vel=0.3,tr=0.1:turn=60
| |
| vel=-0.3,tr=0.1:turn=60
| |
| vel=0.7, edger=-1, white=0: dist=10.0, xb=20, log=0
| |
| | |
| The mission follows right side of line,
| |
| * in a left curve (1mØ) until crossing a line
| |
| * wait for crossing line to disappear,
| |
| * and velocity reach 0
| |
| * make a 3-point 180 degree turn
| |
| * follow the other side of line - now a right curve (until log is full or 10 meters or crossing another black line)
| |
| | |
| The difference between a left and a right curve is the "edger=1.0" and "edger=-1.0", this makes the robot follow the curve with an offset of 1cm towards the center of the curve (more left in a left curve). This gives more space for overshoot when hitting the curve - the sensor range is about +/- 2cm.
| |
| | |
| If the line is no longer valid, then the last curvature is maintained, i.e. there is a chance that the the line will be re-found.
| |
| | |
| ===Heading control===
| |
| | |
| Heading control is not used during a tr=xx based turn, but after such a turn the heading control maintains the end heading.
| |
| The end heading is the start heading plus the turned angle.
| |
| | |
| While driving straight, then the heading control attempts to keep the heading.
| |
| | |
| Heading control is somewhat speed dependent, these paramaters seems to be good at about 0.6 m/s.
| |
| | |
| [[File:heading_control_dialog.png]]
| |
| | |
| A 60 degree turn with an acceleration limit of 1m/s^2 makes a turn like this:
| |
| | |
| [[File:heading_ctrl_20_deg.png]]
| |
| | |
| This curve is generated with the following script:
| |
| | |
| thread=6
| |
| : time=0.01
| |
| vel=0.6, acc=1.0: dist=0.1,time=1
| |
| log=3.0: time=0.1
| |
| tr=0.2: turn=20.0
| |
| : dist=0.3, log=0
| |
| | |
| This is after version 3.612 (from 16 March 2017.
| |
