ESC calibration: Difference between revisions

From Rsewiki
No edit summary
 
(5 intermediate revisions by the same user not shown)
Line 29: Line 29:
Click all mounted motors to manual, Set manual value to 1000 for all motors and press 'Apply manual values'.
Click all mounted motors to manual, Set manual value to 1000 for all motors and press 'Apply manual values'.


=== Connect battery ===
=== Connect battery and set 'stick' to 0 ===


Connect the battery and wait for the motors to beep.
Prepare 0 value for all motors


=== Set to minimum 'stick' ===
Connect the battery and wait for the motors to '''beep twice'''! - then you have 3 seconds to change press the "apply manual values".


Set all values to 0 as shown  
Set all values to 0 as shown by clicking "Apply manual values".
 
If you miss the 3 seconds, then the motors will beep 3 times, 4 times and then back to 2 times.
 
This can be difficult to hear with all motors beeping, so if in trouble, take one motor at a time.


[[File:esc-calibration-min-stick-gui.png | 600px]]
[[File:esc-calibration-min-stick-gui.png | 600px]]


Set values to 0 for all motors and press 'Apply manual values'.
Set values to 0 for all motors and press 'Apply manual values' (and apply within 3 seconds after the first two beeps!).


The motors should now be quit and ready to go.
The motors should now be quit and ready to go.
Line 45: Line 49:
== Test propeller rotation direction ==
== Test propeller rotation direction ==


Use the GUI to set all motors to 10%, i.e. a value of 100, and check that they spin, and in the right direction.
Use the GUI to set all motors to 5-10%, e.g. a value of 70, and check that they spin, and in the right direction.
 
* motor 1 CCV  (seen from above)
* motor 2 CV
* motor 3 CCV
* motor 4 CV
* motor 5 CCV
* motor 6 CV

Latest revision as of 17:58, 2 December 2020

Back to Drone control

ESC calibration

The ESC used her is

  • Hobbywing 40A 3-6 Lipo cell controller.

Manual is here: https://cdn.shopify.com/s/files/1/0109/9702/files/User_s_Manual_Xrotor-en.pdf?7945784144032874852

The calibration instructions are as in this figure, but use the GUI to set the ranges right.

Basic calibration instructions, but replace stick with GUI based calibration.

Gui based ESC calibration

NB!

  • Remove propellers.
  • Disconnect battery

Set to max 'stick'

With the controller connected to the PC and connected to the GUI, set the manual motor value to 1000, as shown below:

Click all mounted motors to manual, Set manual value to 1000 for all motors and press 'Apply manual values'.

Connect battery and set 'stick' to 0

Prepare 0 value for all motors

Connect the battery and wait for the motors to beep twice! - then you have 3 seconds to change press the "apply manual values".

Set all values to 0 as shown by clicking "Apply manual values".

If you miss the 3 seconds, then the motors will beep 3 times, 4 times and then back to 2 times.

This can be difficult to hear with all motors beeping, so if in trouble, take one motor at a time.

Set values to 0 for all motors and press 'Apply manual values' (and apply within 3 seconds after the first two beeps!).

The motors should now be quit and ready to go.

Test propeller rotation direction

Use the GUI to set all motors to 5-10%, e.g. a value of 70, and check that they spin, and in the right direction.

  • motor 1 CCV (seen from above)
  • motor 2 CV
  • motor 3 CCV
  • motor 4 CV
  • motor 5 CCV
  • motor 6 CV