Robobot on Raspberry PI: Difference between revisions
(3 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
Back to [[Robobot]] | Back to [[Robobot]] | ||
== Get ROBOBOT and REGBOT source == | == Get ROBOBOT and REGBOT source == | ||
Line 30: | Line 11: | ||
ln -s regbot/robobot_bridge | ln -s regbot/robobot_bridge | ||
ln -s regbot/regbotgui | ln -s regbot/regbotgui | ||
ln -s regbot/mission && ln -s regbot/robobot_bridge && ln -s regbot/regbotgui | svn co svn://repos.gbar.dtu.dk/jcan/regbot && ln -s regbot/mission && ln -s regbot/robobot_bridge && ln -s regbot/regbotgui | ||
==Update and compile== | ==Update and compile== | ||
Line 65: | Line 46: | ||
Type | Type | ||
cd ~/robobot_bridge | cd ~/robobot_bridge | ||
mkdir -p build # make a build | mkdir -p build # make a build directory; -p accepts it may be there already | ||
cd build | cd build | ||
cmake .. # builds Makefile from CMakeLists.txt in parent directory ".." | cmake .. # builds Makefile from CMakeLists.txt in parent directory ".." | ||
make - | make -j3 # compile - using 3 CPU cores (not to overheat) | ||
cd ~/mission # to C++ version of mission control | cd ~/mission # to C++ version of mission control | ||
mkdir -p build # make a build | mkdir -p build # make a build directory; -p accepts it may be there already | ||
cd build | cd build | ||
cmake .. # builds Makefile from CMakeLists.txt in parent directory ".." | cmake .. # builds Makefile from CMakeLists.txt in parent directory ".." | ||
make - | make -j3 # compile - using 3 CPU cores | ||
=== Start robobot_bridge === | === Start robobot_bridge === | ||
Line 88: | Line 69: | ||
# start ROBOBOT bridge | # start ROBOBOT bridge | ||
cd /home/local/robobot_bridge/build && ./robobot_bridge -a & | cd /home/local/robobot_bridge/build && ./robobot_bridge -a & | ||
Copy and 'shift-ctrl-v' will do | Copy and 'shift-ctrl-v' will do | ||
==REGBOT software== | ==REGBOT software== |
Latest revision as of 12:57, 25 December 2021
Back to Robobot
Get ROBOBOT and REGBOT source
This is probably installed already, otherwise use
cd svn co svn://repos.gbar.dtu.dk/jcan/regbot ln -s regbot/mission ln -s regbot/robobot_bridge ln -s regbot/regbotgui svn co svn://repos.gbar.dtu.dk/jcan/regbot && ln -s regbot/mission && ln -s regbot/robobot_bridge && ln -s regbot/regbotgui
Update and compile
On the raspberry there is the following directories:
$ cd $ ls mission Mission software skeleton that can also access the raspberry camera regbotgui Configuration GUI for REGBOT (python), a Windows executable can be found in course material. regbot/regbot Firmware for the REGBOT part robobot_bridge The connection software between the REGBOT, the small display, the remote control and the mission software
Update
All these source directories are already connected to a SVN repository, but probably need update, by
cd cd mission svn up cd ../regbotgui svn up cd ../regbot svn up cd ../robobot_bridge svn up
Compile
If there are updates, then they need a recompile (except qtgui).
Mission and Robobot_bridge has a 'build' subdirectory with a Makefile, REGBOT has the Makefile in the base directory.
Type
cd ~/robobot_bridge mkdir -p build # make a build directory; -p accepts it may be there already cd build cmake .. # builds Makefile from CMakeLists.txt in parent directory ".." make -j3 # compile - using 3 CPU cores (not to overheat) cd ~/mission # to C++ version of mission control mkdir -p build # make a build directory; -p accepts it may be there already cd build cmake .. # builds Makefile from CMakeLists.txt in parent directory ".." make -j3 # compile - using 3 CPU cores
Start robobot_bridge
The ROBOBOT bridge should start automatically to open the display (showing IP and battery voltage) and optionally also camera streaming (must be installed first)
nano /etc/rc.local
add the following lines before 'exit 0' (close to the end)
# DTU fix for time over blocked network htpdate -q www.linux.org www.freebsd.org # start ROBOBOT bridge cd /home/local/robobot_bridge/build && ./robobot_bridge -a &
Copy and 'shift-ctrl-v' will do
REGBOT software
The REGBOT is programmed with Arduino (and Teensyduino) and require these tools to be installed to compile and install the firmware See the installation procedure description in Software_installation.
The REGBOT software is in the ~/regbot/regbot directory
To compile it for the REGBOT version 4 hardware (red board) with a Teensy 3.5 processor board, go to the '3.5' subdirectory
cd ~/regbot/regbot/3.5 make -j4
If successful a regbot.hex file is generated and should be uploaded to the REGBOT Teensy 3.5 processor.
This can be done from a console with X-messages enabled.
ssh -X local@solvej.local
if the robot is 'solvej'.
NB! While programming all the pins on the processor are released, including the one maintaining power to the robot. This means that the red button on the board MUST be pressed during the MAKE UPLOAD command
cd ~/regbot/regbot/3.5 make upload
See the regbot directory for more details.