User interface: Difference between revisions

From Rsewiki
No edit summary
 
(81 intermediate revisions by the same user not shown)
Line 1: Line 1:


==Screen dumps==
Back to [[regbot | Regbot]] main page


The user interface can configure and run the robot, as well as inspecting almost all values on the robot. Written in python using Qt GUI library.
==Overview==


The interface looks like on figures below.
Connection is either using USB or network if the robot has wifi.


On Windows USB is com3, com4 or any higher, see the device-list in the control panel.


[[File:Gui_robot.png]]
On Linux USB is /dev/ttyACM0 or /dev/ttyACM1 if /dev/ttyACM0 is used for other devices.


Figure 1. The general settings for the robot. The left panel is the general connection status and space for some messages from the robot. The central tab is mostly for configuration of the robot and some sensor and calculated values like pose and tilt. To the right is a fast graph of the last mission.


=== Data logger ===
The user interface can configure and run the robot, as well as inspect almost all values on the robot. Written in python using Qt GUI library.


[[File:Gui_rev0.png]]
The interface looks like on figures below.


Figure 2. The data logging options. A number of sensor values and interface points in the robot software can be logged. The text window shows loaded data from a mission. The log format is designed to be directly compatible with the 'load' function in MATLAB.
In general:
* Yellow fields are read-only (updates from the robot when connected).
* White fields are editable
* Editable fields require (in general) that an "edit" button be pressed first and a "save" button after the edit.
* Many check-boxes get implemented as they are checked/unchecked, but not all.
* Data is updated from the robot at a relatively low update rate; if data is to be used for documentation, then use the onboard log function.


The control details gives detaild at datapoints connected to or inside the general PID controler design used for all control settings. These control datapoints is illustrated in the figure below.


[[File:Gui_control_data_points.png]]
[[File:Gui_robot.png | 800px]]


Figure 3. The general PID controller design with additional optional controller parts. "'''r'''" is reference input. And after the optional "'''pre-filter'''" the reference is compared with the measured value "'''m'''", optionally through a Lead filter. The "'''m-dot'''" is an optionally derivative of the measurement, that can be used for a less noisy Lead (with tau_d as normal, but no pole). The error signal "'''e'''" is fed through a gain "'''Kp'''", an optional Lead and an optional integrator. After this the output "'''u1'''" is summed from "'''up'''" (proportional/Lead), "'''ui'''" integrator term and "uf" from an optional feed forward branch. The output "'''u1'''" can further optionally be integrated (if '''Kz'''=0, if '''Kz'''=1 then the post-integrator has a zero). The output is finally limited to signal "'''u'''".
Figure 1. The general settings for the robot. The left panel is the general connection status and space for some messages from the robot. The central tab is primarily for the configuration of the robot and some sensors and calculated values like pose and tilt. To the right is a fast graph of the last mission.
NB! The data rate is low, so to get an overview, use the log function for more details.


The yellow circles indicate the datapoints that can be logged.
=== Data logger ===


All integrators can be limited. The integrators are further disabled if the output limiter limits the output. Some of the control interfaces (all but the balance controllers) further disables integrators when there is defined an acceleration limit in the mission, and this actually is limiting the acceleration.
[[File:Gui_rev0.png | 800px]]


The "'''post-integrator'''" is usable in the balance controller, as is the "'''m-dot'''" that is connected to tilt velocity from the gyro.
Figure 2. The data logging options. A number of sensor values and interface points in the robot software can be logged. The text window shows loaded data from a mission. The log format is designed to be directly compatible with the 'load' function in MATLAB.


== Manu ==
Use a script like this in MATLAB


[[File:regbot_gui_show_menu.png]]
clear
close all
% Liv (36)
%  1    time 2.005 sec
%  2  3  4  5  (mission 0), state 2, entered (thread 1, line 1), events 0x0 (bit-flags)
%  6  7 Motor voltage [V] left, right: 0.49 -2.11
%  8  9 Encoder left, right: 4294967021 25
% 10 11 Wheel velocity [m/s] left, right: -0.0885 0.0759
% 12 15 Chirp amplitude=0, frequency =0 rad/s, phase=0 rad, value=0
%%
data = '''load('log_position-liv36_b.txt')''';
%% plot motor voltage and velocity
figure(100)
hold off
plot(data(:,1), data(:,6), 'linewidth', 2)
hold on
plot(data(:,1), data(:,10), ':', 'linewidth', 2)
grid on
legend('left voltage [V]', 'left vel [m s^{-1}]', 'location','northwest');
xlabel('Time [sec]')


Figure 4. Other tab pages are available from the "show" menu.
The top text lines of the log file are copied to the MATLAB script to ease the identification of data to plot.


==Mission==
====ACC and gyro====


Mission specification consist of mission lines, each line consist of two (lower case) parts divided by ':'
Acceleration logs the acceleration values in m/s^2 on all 3 axes (x (forward if in balance),y (left), z (up if in balance))


Burde formuleres efter EBNF
Gyro is rotation velocity around the same 3-axis. Unit is degrees per second (after calibration offset).
* mission = mission_line, { mission line };
* mission line = [drive parameter list], [':' , continue condition list];
*drive parameter list = ...


The short form:
====Encoder====


drive parameter: continue condition (conditions are OR'ed)  
Encoder values for wheel rotation (left, right) 48 values per rotation, increases on forward.


e.g.:
====Motor voltage====


vel=-0.2, acc=3.0 : dist=1, time=12
Is the motor voltage - before conversion to PWM, compensated for changes in battery voltage.


Drive backwards at a speed of 0.2m/s, accelerate with 3m/s2 for 1 meter (or max 12 seconds)
====Motor current====


=== Drive values ===
Filtered current sensor values. zero current is calibrated just before the start of a mission - this calibration sometimes makes a mistake, resulting in a wrong offset of the logged current. Value is in Amps. The value is filtered to match the log interval if the interval is > 2ms.


* VEL is velocity in m/s - positive is forward, 0=stop. uses last value if omitted.
====Wheel velocity====


* ACC is acceleration limit in m/s2. Uses last value if omitted.
Based on the time between encoder tics. If more tics are within 1 ms, then the interval time is averaged. When there is a long time between tics (>50ms), then the time since the last tick is used to calculate velocity, i.e. velocity goes towards zero with time if no encoder pulses arrive.


* TR is turnradius in metre - positive, 0 is turn on the spot. straight if omitted. NB! in balance the minimum turn radius is about 0.07m, as balance requires that at least one wheel can give a forward acceleration.
==== Turn rate ====


The turn rate is based on encoder tics (not the gyro), the unit is radian/sec


* BAL is balancing, uses last value if omitted.
==== Robot pose ====


* HEAD is reference heading in degrees (-180 .. 180), set at start of line.
The robot pose is position since the start of the mission (odometry coordinates), x,y,h,t where h is heading in radians (positive counterclockwise), and t is a tilt in radians (zero is in balance, positive is forward).


====Log====
==== Line sensor ====


* LOG is log interval in milliseconds. Once started it continues until buffer is full.
All values related to the line sensor, including AD value from each sensor.


To log a velocity step response, a mission could be:
==== IR sensor ====


vel=0.3,log=1:time=0.3
Is distance converted to meters for each sensor (default is sensor 1 to the right and sensor 2 is forward).
vel=0.5:log=0
==== Battery ====


The first line starts the robot with a velocity of 0.3m/s and starts logging (log=1) the log value is log interval in ms.
Battery voltage in Volts.


After 0.3 seconds velocity is stepped to 0.5m/s until the log is full (the log=0 after the ':')
==== Extra ====


Note that the log is generated in RAM on the robot with limited space (approximately 30kBytes), so limit the interface points logged to get longer logging time.
Debug feature for log of extra values.


====GOTO====
==== Mission ====


* LABEL is a label number that can be used by GOTO.
State, Thread, Line, Event. Where State is mission state (should always be 2 or 8 when stopping), thread number and line number in that thread, for the latest line activated (if more than one is activated in the same log interval, then the latest is logged. An event is a 32-bit integer where each bit corresponds to an event number, and events are accumulated over the logging period.


* GOTO is a jump to the label number given. This can be limited to COUNT use of goto, the count is then reset after the first skip. The goto can also be skipped if any other conditions are true when this line is reached. A line with a goto will never wait.
==== Motor ref ====


See a GOTO example below under threads.
Is the desired motor velocity (input to velocity controller) - in m/s


====Line-sensor====
==== Control time ====


If a line sensor is installed, then the following should work too:
Is the time taken to handle sensor data, calculate control values and advance in mission lines - this should be finised within 1ms. Value is in microseconds, so it should be below 1000 to ensure valid control calculations.


* EDGER is following Right edge of line at -2..2 (in cm), positive is right
==== Control details ====


* EDGEL is following Left edge of line at -2..2 (in cm), positive is right
Value order: r, m, m2, uf, r2, ep, up, ui, u1, u


* WHITE set to 1 if follow-line tape is white, else 0
The control details give details at data points connected to or inside the general PID controller design used for all control settings. These control data points are illustrated in the figure below.


====Distance sensor====
===Controller configuration===


If IR distance sensors are installed, then these should work:
All controllers can be configured from the "control" tab. See the [[Control]] page for more control details.


* IRSENSOR is IR-sensor to use (1 is distance to a wall, and 2 is distance in front).
[[File:Gui_control.png | 800px]]


* IRDist is IR-distance to hold.
Figure 4b. All control values are set from this page; click on the relevant controller and enter the relevant values in the dialogue window shown below.


====Servos====
[[File:Gui_control_dialog.png | 500px]]


Control of servos, there is support for up to 3 servos (version 3 only).
Figure 5. This dialogue configures the wheel velocity controller - shown as a PI-Lead-controller with feed-forward and an output limit at (+/-) 9V. All other options are disabled. The blue frame boxes indicate a traditional PID controller with lead in forward (and)/or in the feedback branch.
There is 2 extra pins, one analog pin DAC (called servo 4) (real D/A converter) and one digital pin (24) called servo 5.


* SERVO=N PSERVO=XXX where N is servo number (1..5) and XXX is servo position, for servo 1,2 and 3 value is in range +/- 1000, where 0 is 1.5 ms, +500 is 2ms, + 1000 is 2.5ms, -500 is 1ms and -1000 is 0.5ms pulse with with at pulse frequency of 333 Hz. For servo 4 value is analog value -1000 is minimum and +1000 is maximum. for servo 5 (digital pin) XXX=0 is Low (0V) and XXX=1 is High (3.3V).
When "enable controller" is disabled, then the control is disabled.  


====Threads====
To use feed-forward only (i.e. set output directly from ref), enable controller, but set Kp=0, and enable feed-forward with some value for Kf (when Kf = 1, then ref is used directly as output).


A command sequence may be divided into threads. The default thread has number 1.
NB! As velocity measurements are rather noisy, the filter in the feedback path (Lead/Lag feedback) could be implemented as a low-pass filter with tau_zero = 0 and tau_pole = 0.005 (recommended).


* THREAD=3 means that this and all following lines are handled by one thread (with number 3). All threads are activated at time 0.
=== IMU===


Example
The IMU page shows data from the IMU and is used for tilt measurement for the balance controller only.
thread=0
    log=20: log=0
    event=0
thread=2
    label=1
    vel=0.4: time=1.0
    vel=0.2: time=1.0
    vel=0.0: time=1.0
    event=3 : event=7
    vel=0.2, tr=0.15:turn=90
    goto=1
thread=9
    bal=0:event=3
    bal=1: time=2
    label=12
    event=7:time=0.1
    goto=12
thread=10
    label=20,servo=1,pservo=-300:time=1
    servo=1,pservo=200:time=1
    goto=20


Thread 0: This thread controls the logging function with the condition 'log=0' that is true when the log is full,
[[File:Gui_IMU.png | 800px]]
then the mission is stopped. 'event=0' is a special event that stops the mission.


Thread 2: This thread controls velocity in three steps 0.4m/s, 0.2 m/s and 0m/s, then sends an event (event=3) and waits for event 7.
Figure 5.1 IMU data. The graph shows calibrated values, and the gyro is calibrated by keeping the robot stable and pressing the "calibrate" button. (remember to save the result in robot flash). The servos drift slightly, so repeat if needed.
When event 7 arrives then the robot turns 90 degrees and starts over.


Thread 9: This thread controls the balance. Starts with no balance, until event 3 occurs, then goes into balance mode and waits 2 seconds (to stabalize in balance). Then it enters a loop that emits event 7 every 0.1 second, to keep thread 2 going.
A new feature has been added to set the orientation of the IMU board, but it is not shown in the image.


Thread 10: this is a servo control thread, that moves servo 1 between 2 positions.
=== Menu ===


The mission is finished when all threads has ended, in this case when the log is full.


The thread number is pt. not used to determine the execution order of the threads (uses script order).


====Events====
[[File:regbot_gui_show_menu.png | 600px]]


Events can be generated if an event=X command is entered in the parameter side of the colon. The event is activated when the line is activated.
Figure 6. Other tab pages are available from the "show" menu.
More than one event can be activated in the same line, e.g.:


vel=0.2,event=7,event=12:time=1
===Mission===
event=0


Here event 7 and 12 are activated at the same time as the velocity is set to 0.2.
Missions are entered through the mission tab:


Event 0 has a special meaning and will terminate full mission NOW!
[[File:Gui_mission.png | 700px]]


Events are used in the example above.
Figure 7. Missions are entered in the left (white) area, and can be syntax tested with the button above.
The result of the check is shown in the yellow area (right).
The mission of the robot can be fetched to the right area.
Missions (the left area) can be saved and loaded from text files with the buttons below.


===Continue conditions===
If you copy-paste from another application, so make sure not to include any formatting; 7-bit ASCII characters are allowed only.


':' is separation of parameters and continue condition.
Missions are not saved to the robot before you press "save to robot".  


* DIST is driven distance in this mission line - positive meters
The mission is lost for the robot after a power cycle unless you save the configuration to robot flash - using the "save to robot flash" in the left pane.
* TURN is angle turned in this mission line - degrees, positive is Left (CCW if forward speed)
* TIME is max time in this mission line - positive seconds
* COUNT is used with GOTO and GOTO will be ignored, if this line is executed more than this count
* XB,XW,LV is conditions relevant for the line sensor (if implemented) - see below
* IR1,IR2 is conditions relevant for IR distance sensors - se below
* TILT is tilt angle (especially useful if not in balance.
* EVENT is testing for events
* LOG is true when log is full (value is ignored, but must be set to a number (e.g. 0))
* HEAD is absolute heading test, head=175 is true if actual heading is within 3 degrees of this value. head>XXX and head<YYY compares with current value, but is difficult to use when crossing the +/- 180 deg border.


The equal (=) sign can for some values (dist, turn, xb, xw and tilt) be replaced by '<' or '>', for most values (except xb, xw and head) an equal sign means equal or greater. NB! '>=', '==', '<=' and '!=' are not valid.
==== Mission lines ====


Example: Drive 0.2m then turn 30 deg to the right (turn radius=0, but will be more with acceleration being only 1m/s2) then drive another 1 second at a higher speed (or maximum 0.4m).
Mission specification consists of mission lines; each line consists of two (lower case) parts divided by ':'


  vel=0.2,acc=1 : dist=0.2
  drive parameter: continue condition
tr=0 : turn = -30
vel=0.5 : dist=0.4,time=1


Example Zig-zag sideways: drive 0.2m backwards and then turn 45 deg left, 45 deg right and a bit forward, repeated 2 times more with a goto (to label=6).
continue conditions are OR'ed.


vel=-0.2, acc=2.0: dist=0.2
e.g.:  
label=6:
tr=0.15: turn=45.0
tr=0.15: turn=-45.0
vel=0.2:dist=0.18
vel=-0.2,goto=6: count=2


==== Line sensor ====
  vel=-0.2, acc=3.0 : dist=1, time=12
 
This section is valid if a line sensor is installed and calibrated. Use "Edge" tab for calibration (put edge sensor "ON" and on a dark background and press "Calibrate no reflection" and then on a bright background and press "Calibrate white reflection", then "save on robot").
 
* XB, XW is test for crossing black/white line, value is 0..20, 0 is true on no crossing, 1..20 is confidence in crossing (20 is highest)
* LV is test for valid line 0=true for no valid line, 1=true for valid line. NB! A wooden (or dirty) floor is likely to give a valid line at times.
 
Example: Drive until a crossing black line is found or 2.5m is driven, then continue until the crossing line is gone (reached other side of line) and stop
 
  vel=0.2, log=5, acc=2: xb>16, dist=2.5
:xb < 4,dist=0.2
vel=0:time=0.1
 
Example find white line and follow edge: Drive until (white) line is found - as before - then turn to the right and follow line for 0.5 m.
 
vel=0.2, log=5, acc=2: xw>16, dist=2.5
:xw < 4,dist=0.2
vel=0:time=0.3
tr=0,vel=0.2:turn=-90
edgel=0, white=1: dist=0.5
 
NB! testing of crossing white or black is unsafe if in balance (requires good calibration in balance). And if the front is raised, then this feature do not work at all.
 
==== Distance sensor====
 
IR1, IR2 is test for distance measured by IR sensor.
 
@todo Distance sensor is not tested much, and is therefore assumed not to work properly.
 
==== Tilt balance angle ====
 
TILT is test for tilt angle (0 is balance point)
 
Example:
@todo
 
==== Events ====
 
An event can be a test condition in a mission line, and can be generated by a mission line.
Up to 32 events can be used, they are named "event=N", where N is a number in the range [0..31].
An event is valid for one sample period only (1ms).
 
Events can be created from the communication interface with the command like
<event=5>
 
An example could be like this (a not very functional example)
 
thread=2
  vel=0.2:time=1         # driving at speed 0.2 m/s for 1 second
  vel=0,event=7:event=5  # set speed to 0 and generate event 7, then wait for event 5
  vel=0.2:time=1          # speed back to 0.2 m/s in 1 second
  vel=0                  # stop this thread
thread=8
  label=1:time=5,event=7  # wait for event 7 (generated after 1 second by thread 2) or for maximum 5 seconds (should never happen)
  event=12:time=1        # generate event 12 (and wait for 1 second)
  event=13:time=1        # generate event 13 (and wait for 1 second before ending this thread
 
The mission will not end before the user has generated event 5 (by sending "<event=5>").
Every time an event is generated a message is send to the client line, for this mission the following messages will be generated:
 
# event 7
# event 12
# event 13
# event 5    (this in response to a user event)
 
Event 0 can't be tested, it will terminate the mission immediately.
 
===Examples===
 
Example drive-turn-drive-turn at 20cm/s:
 
vel=0.2, acc=1.5 : dist = 0.5, time=5
tr=0.15 : turn=90
: dist = 0.5
tr=0.15 : turn=90
vel=0 : time=1
 
Example wait 5 seconds:
 
vel=0 : time=5
 
Example balance and follow line: Go on balance and follow left edge of white line for 0.5m, then follow line for another 0.5m without balance.
 
vel=0.2,edgel=0,white=1,bal=1: dist>0.5
bal=0,edgel=0,white=1:dist=0.5
 
NB! Most examples - and especially balance - requires valid controller parameters and calibrated sensors (tilt offset for balance).
 
===Save ===
Transfer the mission to the robot RAM by pressing "Save" (top right), the mission will be lost by a reboot or power off, unless saved on robot!


Save the mission on the robot flash memory (EE-prom) by pressing "save on Robot" (left panel). NB! The space is limited (about 100 lines)!
Drive backwards at a speed of 0.2m/s, and accelerate with 3m/s2 to this speed until a distance of 1 meter is driven or 12 seconds have passed.


The mission can also be saved in a text-file using the bottom right save button
See [[Mission]] for more details.

Latest revision as of 09:09, 17 November 2023

Back to Regbot main page

Overview

Connection is either using USB or network if the robot has wifi.

On Windows USB is com3, com4 or any higher, see the device-list in the control panel.

On Linux USB is /dev/ttyACM0 or /dev/ttyACM1 if /dev/ttyACM0 is used for other devices.


The user interface can configure and run the robot, as well as inspect almost all values on the robot. Written in python using Qt GUI library.

The interface looks like on figures below.

In general:

  • Yellow fields are read-only (updates from the robot when connected).
  • White fields are editable
  • Editable fields require (in general) that an "edit" button be pressed first and a "save" button after the edit.
  • Many check-boxes get implemented as they are checked/unchecked, but not all.
  • Data is updated from the robot at a relatively low update rate; if data is to be used for documentation, then use the onboard log function.


Figure 1. The general settings for the robot. The left panel is the general connection status and space for some messages from the robot. The central tab is primarily for the configuration of the robot and some sensors and calculated values like pose and tilt. To the right is a fast graph of the last mission. NB! The data rate is low, so to get an overview, use the log function for more details.

Data logger

Figure 2. The data logging options. A number of sensor values and interface points in the robot software can be logged. The text window shows loaded data from a mission. The log format is designed to be directly compatible with the 'load' function in MATLAB.

Use a script like this in MATLAB 

clear
close all
% Liv (36)
%  1    time 2.005 sec
%  2  3  4  5   (mission 0), state 2, entered (thread 1, line 1), events 0x0 (bit-flags)
%  6  7 Motor voltage [V] left, right: 0.49 -2.11
%  8  9 Encoder left, right: 4294967021 25
% 10 11 Wheel velocity [m/s] left, right: -0.0885 0.0759
% 12 15 Chirp amplitude=0, frequency =0 rad/s, phase=0 rad, value=0
%%
data = load('log_position-liv36_b.txt');
%% plot motor voltage and velocity
figure(100)
hold off
plot(data(:,1), data(:,6), 'linewidth', 2)
hold on
plot(data(:,1), data(:,10), ':', 'linewidth', 2)
grid on
legend('left voltage [V]', 'left vel [m s^{-1}]', 'location','northwest');
xlabel('Time [sec]')

The top text lines of the log file are copied to the MATLAB script to ease the identification of data to plot.

ACC and gyro

Acceleration logs the acceleration values in m/s^2 on all 3 axes (x (forward if in balance),y (left), z (up if in balance))

Gyro is rotation velocity around the same 3-axis. Unit is degrees per second (after calibration offset).

Encoder

Encoder values for wheel rotation (left, right) 48 values per rotation, increases on forward.

Motor voltage

Is the motor voltage - before conversion to PWM, compensated for changes in battery voltage.

Motor current

Filtered current sensor values. zero current is calibrated just before the start of a mission - this calibration sometimes makes a mistake, resulting in a wrong offset of the logged current. Value is in Amps. The value is filtered to match the log interval if the interval is > 2ms.

Wheel velocity

Based on the time between encoder tics. If more tics are within 1 ms, then the interval time is averaged. When there is a long time between tics (>50ms), then the time since the last tick is used to calculate velocity, i.e. velocity goes towards zero with time if no encoder pulses arrive.

Turn rate

The turn rate is based on encoder tics (not the gyro), the unit is radian/sec

Robot pose

The robot pose is position since the start of the mission (odometry coordinates), x,y,h,t where h is heading in radians (positive counterclockwise), and t is a tilt in radians (zero is in balance, positive is forward).

Line sensor

All values related to the line sensor, including AD value from each sensor.

IR sensor

Is distance converted to meters for each sensor (default is sensor 1 to the right and sensor 2 is forward).

Battery

Battery voltage in Volts.

Extra

Debug feature for log of extra values.

Mission

State, Thread, Line, Event. Where State is mission state (should always be 2 or 8 when stopping), thread number and line number in that thread, for the latest line activated (if more than one is activated in the same log interval, then the latest is logged. An event is a 32-bit integer where each bit corresponds to an event number, and events are accumulated over the logging period.

Motor ref

Is the desired motor velocity (input to velocity controller) - in m/s

Control time

Is the time taken to handle sensor data, calculate control values and advance in mission lines - this should be finised within 1ms. Value is in microseconds, so it should be below 1000 to ensure valid control calculations.

Control details

Value order: r, m, m2, uf, r2, ep, up, ui, u1, u

The control details give details at data points connected to or inside the general PID controller design used for all control settings. These control data points are illustrated in the figure below.

Controller configuration

All controllers can be configured from the "control" tab. See the Control page for more control details.

Figure 4b. All control values are set from this page; click on the relevant controller and enter the relevant values in the dialogue window shown below.

Figure 5. This dialogue configures the wheel velocity controller - shown as a PI-Lead-controller with feed-forward and an output limit at (+/-) 9V. All other options are disabled. The blue frame boxes indicate a traditional PID controller with lead in forward (and)/or in the feedback branch.

When "enable controller" is disabled, then the control is disabled.

To use feed-forward only (i.e. set output directly from ref), enable controller, but set Kp=0, and enable feed-forward with some value for Kf (when Kf = 1, then ref is used directly as output).

NB! As velocity measurements are rather noisy, the filter in the feedback path (Lead/Lag feedback) could be implemented as a low-pass filter with tau_zero = 0 and tau_pole = 0.005 (recommended).

IMU

The IMU page shows data from the IMU and is used for tilt measurement for the balance controller only.

Figure 5.1 IMU data. The graph shows calibrated values, and the gyro is calibrated by keeping the robot stable and pressing the "calibrate" button. (remember to save the result in robot flash). The servos drift slightly, so repeat if needed.

A new feature has been added to set the orientation of the IMU board, but it is not shown in the image.

Menu

Figure 6. Other tab pages are available from the "show" menu.

Mission

Missions are entered through the mission tab:

Figure 7. Missions are entered in the left (white) area, and can be syntax tested with the button above. The result of the check is shown in the yellow area (right). The mission of the robot can be fetched to the right area. Missions (the left area) can be saved and loaded from text files with the buttons below.

If you copy-paste from another application, so make sure not to include any formatting; 7-bit ASCII characters are allowed only.

Missions are not saved to the robot before you press "save to robot".

The mission is lost for the robot after a power cycle unless you save the configuration to robot flash - using the "save to robot flash" in the left pane.

Mission lines

Mission specification consists of mission lines; each line consists of two (lower case) parts divided by ':' 

drive parameter: continue condition

continue conditions are OR'ed.

e.g.: 

vel=-0.2, acc=3.0 : dist=1, time=12

Drive backwards at a speed of 0.2m/s, and accelerate with 3m/s2 to this speed until a distance of 1 meter is driven or 12 seconds have passed.

See Mission for more details.

Retrieved from "https://rsewiki.electro.dtu.dk/index.php?title=User_interface&oldid=6533"