Design calculations: Difference between revisions
No edit summary |
|||
| (9 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
Back to [[Regbot]] main page | |||
== Maximum speed== | == Maximum speed== | ||
| Line 6: | Line 9: | ||
This gives a max speed of 5600/60/9.68*0.06*Pi = 1.8m/s | This gives a max speed of 5600/60/9.68*0.06*Pi = 1.8m/s | ||
(with a maximum motor voltage of 9V should - for short periods - allow up to 2.7m/s). | |||
== Encoder calculations== | == Encoder calculations== | ||
| Line 17: | Line 22: | ||
Speed is calculated based on time between encoder ticks | Speed is calculated based on time between encoder ticks | ||
At max speed there should be approx 4.48 encoder ticks per ms, or 223 us between tics | At max speed there should be approx 4.48 encoder ticks per ms, or 223 us between tics. | ||
If there is more than one encoder tick within 1ms, then the velocity is averaged over 1 ms. At lower speed the velocity gets updated at every tick time (fewer than one encoder tick in 1 ms). | |||
If time between encoder pulses is more than 0.5 sec, then speed is set to 0. | |||
If time since last encoder tick is longer than last encoder tick period, then velocity is based on time since last tick (up to 0.5 sec, where the speed is set to 0). I.e. the minimum speed measured is 2*0.0041 m/s = 0.81cm/sec. | |||
Sample time is (pt.) 1ms. | Sample time is (pt.) 1ms. | ||
| Line 25: | Line 31: | ||
At low speed the time between encoder ticks make the calculated wheel velocity delayed, resulting in poor controller performance (or even instability). | At low speed the time between encoder ticks make the calculated wheel velocity delayed, resulting in poor controller performance (or even instability). | ||
A velocity estimator is implemented based on anchor voltage and current velocity. This is then high-pass filtered and added to the encoder based velocity. | A velocity estimator is implemented based on anchor voltage and current velocity. This is then high-pass filtered and added to the encoder based velocity. | ||
This function currently disabled - gave problems while balancing. | |||
The motor big controller has problems with low (and high) PWM values at the used 20kHz switch rate. This gives almost no motor power if PWM is less than 7-10%. | |||
Lower switch frequency may give problems with audio noise and high peak current in anchor coils. The tiny motor controller has much higher BW, but noise from switching can give false encoder pulses, and thus there is mounted 1-4.7nF filter capacitors on the encoder lines. | |||
== Parameter estimation== | == Parameter estimation== | ||
| Line 30: | Line 40: | ||
Pololu say that at 6V stall current is 2.2A, or R_A = 2.7 Ohm | Pololu say that at 6V stall current is 2.2A, or R_A = 2.7 Ohm | ||
On this robot the total anchor resistance is estimated to 3.3 Ohm (including H-bridge and wires) based on current step | On this robot the total anchor resistance is estimated to about 3.3 Ohm (including H-bridge and wires) based on current step response. | ||
Latest revision as of 08:50, 24 May 2019
Back to Regbot main page
Maximum speed
Motor has 5600 RPM at 6V no load. Gearing is 9.68:1 Wheel diameter is 6cm.
This gives a max speed of 5600/60/9.68*0.06*Pi = 1.8m/s
(with a maximum motor voltage of 9V should - for short periods - allow up to 2.7m/s).
Encoder calculations
The encoder has 48 ticks per revolution. This gives 48*9.68 = 464.64 ticks per wheel revolution, or Distance per tick = pi*0.06/464.64 = 0.40568 mm/tick
Speed calculation
Speed is calculated based on time between encoder ticks
At max speed there should be approx 4.48 encoder ticks per ms, or 223 us between tics. If there is more than one encoder tick within 1ms, then the velocity is averaged over 1 ms. At lower speed the velocity gets updated at every tick time (fewer than one encoder tick in 1 ms). If time between encoder pulses is more than 0.5 sec, then speed is set to 0. If time since last encoder tick is longer than last encoder tick period, then velocity is based on time since last tick (up to 0.5 sec, where the speed is set to 0). I.e. the minimum speed measured is 2*0.0041 m/s = 0.81cm/sec.
Sample time is (pt.) 1ms.
At low speed the time between encoder ticks make the calculated wheel velocity delayed, resulting in poor controller performance (or even instability). A velocity estimator is implemented based on anchor voltage and current velocity. This is then high-pass filtered and added to the encoder based velocity. This function currently disabled - gave problems while balancing.
The motor big controller has problems with low (and high) PWM values at the used 20kHz switch rate. This gives almost no motor power if PWM is less than 7-10%. Lower switch frequency may give problems with audio noise and high peak current in anchor coils. The tiny motor controller has much higher BW, but noise from switching can give false encoder pulses, and thus there is mounted 1-4.7nF filter capacitors on the encoder lines.
Parameter estimation
Pololu say that at 6V stall current is 2.2A, or R_A = 2.7 Ohm
On this robot the total anchor resistance is estimated to about 3.3 Ohm (including H-bridge and wires) based on current step response.
