Terrain hopper steering: Difference between revisions
No edit summary |
|||
| (9 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
Overview of new steering | Back to [[TerrainHopper]] | ||
== Steering == | |||
Distance between axles is 0.93 m | |||
Distance between king pins 0.55 m | |||
Max steering angle actual is about 32 degrees (center heading) | |||
Steering is limited to +/- 28 degrees in RHD, this gives a turning radius of 2m. | |||
Steering is sensed by RHD plugin "as5047x2", that receives data from encoder interface - a teensy. | |||
The steering angle (in degrees * 10 - positive left) is then transferred to "roboteq-can" RHD plugin, where the steer controller is implemented - and limited to +/- 28 degrees. | |||
==CAD drawings== | |||
See https://cad.onshape.com/documents/97c36fb21a7a858c57c0af9f/w/0d867586bc28d7a9194d7ff3/e/ca0f539fa3eee3cfe0ed4130 | |||
==Overview of new steering== | |||
[[File:off-the-shelf-parts.png | 600px]] | [[File:off-the-shelf-parts.png | 600px]] | ||
Figure 1. New steering part maintaining original steering axle position, but | |||
replacing with bearings and a belt drive to a maxon gear motor. | |||
This figure points to most of the off-the-shelf parts used. | |||
See purchase detail in Terrain-hopper binder (Christian office - red binder). | |||
[[File:modified-parts.png | 800px]] | [[File:modified-parts.png | 800px]] | ||
Figure 2. New steering part maintaining original steering axle position, but | |||
replacing with bearings and a belt drive to a maxon gear motor. | |||
This figure points to most of the parts that needs workshop assistance. | |||
Most of the parts - except axlesl (7 and 8) - can be manufactored on own workshop. The axles will be manufactored by axle supplier. | |||
==Maxon motor== | |||
The motor for steering is a Gear-motor-encoder combination from Maxon: | |||
GEAR | |||
Planetary Gearhead GP 52 | |||
C Ø52 mm, 4 - 30 Nm, Ceramic Version | |||
Outer diameter: 52 mm | |||
Reduction: 81 : 1 | |||
Max. continuous torque: 30 Nm | |||
Part No.: 223093 (345€) | |||
MOTOR | |||
RE 40 Ø40 mm, Graphite Brushes, 150 Watt | |||
Part No.: 148867 (347€) | |||
Outer diameter: 40 mm | |||
Type power: 150 W | |||
Nominal voltage: 24 V | |||
No load speed: 7580 rpm | |||
Nominal torque (max. continuous torque): 177mNm | |||
SENSOR | |||
Encoder MR, Type L, 256 | |||
CPT, 3 Channels, with Line Driver (5V) | |||
Counts per turn: 256 | |||
Number of channels: 3 | |||
Line Driver: Yes | |||
Part No.: 225783 (93€) | |||
Sensor has 10 pins, but cable is a 8 pole network cable, cable colors and (pin number (rj45 end)) | |||
1 NC | |||
2 VCC - blue/white (5) | |||
3 GND - blue (4) | |||
4 nc | |||
5 Ainv - orance/white (1) | |||
6 A - orange (2) | |||
7 Binv - green/white (3) | |||
8 B - green (6) | |||
9 Iinv - brown/white (7) | |||
10 I - brown (8) | |||
The Maxon encoder sensor is not used (march 2019) | |||
Latest revision as of 14:55, 3 July 2019
Back to TerrainHopper
Steering
Distance between axles is 0.93 m
Distance between king pins 0.55 m
Max steering angle actual is about 32 degrees (center heading)
Steering is limited to +/- 28 degrees in RHD, this gives a turning radius of 2m.
Steering is sensed by RHD plugin "as5047x2", that receives data from encoder interface - a teensy.
The steering angle (in degrees * 10 - positive left) is then transferred to "roboteq-can" RHD plugin, where the steer controller is implemented - and limited to +/- 28 degrees.
CAD drawings
Overview of new steering
Figure 1. New steering part maintaining original steering axle position, but replacing with bearings and a belt drive to a maxon gear motor. This figure points to most of the off-the-shelf parts used.
See purchase detail in Terrain-hopper binder (Christian office - red binder).
Figure 2. New steering part maintaining original steering axle position, but replacing with bearings and a belt drive to a maxon gear motor. This figure points to most of the parts that needs workshop assistance. Most of the parts - except axlesl (7 and 8) - can be manufactored on own workshop. The axles will be manufactored by axle supplier.
Maxon motor
The motor for steering is a Gear-motor-encoder combination from Maxon:
GEAR
Planetary Gearhead GP 52 C Ø52 mm, 4 - 30 Nm, Ceramic Version Outer diameter: 52 mm Reduction: 81 : 1 Max. continuous torque: 30 Nm Part No.: 223093 (345€)
MOTOR
RE 40 Ø40 mm, Graphite Brushes, 150 Watt Part No.: 148867 (347€) Outer diameter: 40 mm Type power: 150 W Nominal voltage: 24 V No load speed: 7580 rpm Nominal torque (max. continuous torque): 177mNm
SENSOR
Encoder MR, Type L, 256 CPT, 3 Channels, with Line Driver (5V) Counts per turn: 256 Number of channels: 3 Line Driver: Yes Part No.: 225783 (93€)
Sensor has 10 pins, but cable is a 8 pole network cable, cable colors and (pin number (rj45 end))
1 NC 2 VCC - blue/white (5) 3 GND - blue (4) 4 nc 5 Ainv - orance/white (1) 6 A - orange (2) 7 Binv - green/white (3) 8 B - green (6) 9 Iinv - brown/white (7) 10 I - brown (8)
The Maxon encoder sensor is not used (march 2019)
