Drone compass calibration: Difference between revisions
No edit summary |
|||
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
back to [[Drone control] | back to [[Drone control]] | ||
== Calibration setup == | == Calibration setup == | ||
| Line 8: | Line 8: | ||
Run the calibration app - in the bin directory for Linux, or here for other platforms https://www.pjrc.com/store/prop_shield.html | Run the calibration app - in the bin directory for Linux, or here for other platforms https://www.pjrc.com/store/prop_shield.html | ||
=== Compass calibration app === | |||
If on Linux go to | |||
cd mobotware/drone_ctrl/trunk/CalibrateSensors | |||
./MotionCal | |||
[[File:compass-calibrate-app.png | 400px]] | [[File:compass-calibrate-app.png | 400px]] | ||
Calibration app - with a fair set of values. | Calibration app - with a fair set of values. | ||
Runs directly on Ubuntu 18.04, for Ubuntu 20.04 see below | |||
==== Ubuntu 20.04 ==== | |||
The calibration app is rather old, so it asks for libpng12.so.0. | |||
I managed to install it through package nsight-systems | |||
sudo apt install nsight-systems | |||
cd /usr/lib/x86_64-linux-gnu | |||
sudo ln -s ../nsight-systems/Host-x86_64/libpng12.so.0 | |||
Another option is to get the source code, but the Makefile asks for wxwidgets/3.0.2.gtk2-opengl/bin/wx-config, which I couldn't find. | |||
== Arduino code for compas calibration == | |||
In arduino open the calibration firmware in mobotware/drone_ctrl/trunk/CalibrateSensors | |||
Run the arduino version, where you have installed the Teensyduino and open the CalibrateSensors.ino | |||
In my case | |||
cd mobotware/drone_ctrl/trunk/CalibrateSensors | |||
/home/chr/Downloads/arduino-1.8.13/arduino | |||
* Select board Teensy3.5 | |||
* Compile | |||
* upload (to /dev/ttyACM0 or the port to which the Teensy is connected) | |||
[[File:arduino-compass-calibrate.png | 400px]] | [[File:arduino-compass-calibrate.png | 400px]] | ||
Arduino with sensor calibration code. Sending raw data to app and receive the calibration data when send is pressed on the calibration app. | Arduino with sensor calibration code. Sending raw data to app and receive the calibration data when send is pressed on the calibration app. | ||
== Rotate drone and save result == | |||
In the Calibration app, clear the buffer when you are ready to rotate the drome in all directions. | |||
* press 'clear' | |||
Rotate the drone in all directions, until you get a sphere or an ellipsoid as in the figure above. | |||
I got a 'Fit error' of 2.3% and gaps of just 1.1% - seems to be OK, in the above figure it is even lower. | |||
When it looks good, upload to the Teensy by "Send Cal" | |||
* press 'send Cal' | |||
And the reply should be a green tick-mark as shown. | |||
It is then saved in the Teensy flash (addresses below the first 512 bytes, that is not used by the drone firmware). | |||
== Reload drone control firmware == | |||
Go back to the drone_ctrl directory and reload | |||
cd mobotware/drone_ctrl/trunk/drone_ctrl | |||
make | |||
make upload | |||
The new compas calibration should be in effect. | |||
Latest revision as of 13:17, 2 December 2020
back to Drone control
Calibration setup
Once the controller is mounted on the drone, it is time to calibrate the compass.
Upload the calibration firmware to the Teensy (using the Arduino GUI)
Run the calibration app - in the bin directory for Linux, or here for other platforms https://www.pjrc.com/store/prop_shield.html
Compass calibration app
If on Linux go to
cd mobotware/drone_ctrl/trunk/CalibrateSensors ./MotionCal
Calibration app - with a fair set of values. Runs directly on Ubuntu 18.04, for Ubuntu 20.04 see below
Ubuntu 20.04
The calibration app is rather old, so it asks for libpng12.so.0.
I managed to install it through package nsight-systems
sudo apt install nsight-systems cd /usr/lib/x86_64-linux-gnu sudo ln -s ../nsight-systems/Host-x86_64/libpng12.so.0
Another option is to get the source code, but the Makefile asks for wxwidgets/3.0.2.gtk2-opengl/bin/wx-config, which I couldn't find.
Arduino code for compas calibration
In arduino open the calibration firmware in mobotware/drone_ctrl/trunk/CalibrateSensors
Run the arduino version, where you have installed the Teensyduino and open the CalibrateSensors.ino
In my case
cd mobotware/drone_ctrl/trunk/CalibrateSensors /home/chr/Downloads/arduino-1.8.13/arduino
- Select board Teensy3.5
- Compile
- upload (to /dev/ttyACM0 or the port to which the Teensy is connected)
Arduino with sensor calibration code. Sending raw data to app and receive the calibration data when send is pressed on the calibration app.
Rotate drone and save result
In the Calibration app, clear the buffer when you are ready to rotate the drome in all directions.
- press 'clear'
Rotate the drone in all directions, until you get a sphere or an ellipsoid as in the figure above.
I got a 'Fit error' of 2.3% and gaps of just 1.1% - seems to be OK, in the above figure it is even lower.
When it looks good, upload to the Teensy by "Send Cal"
- press 'send Cal'
And the reply should be a green tick-mark as shown.
It is then saved in the Teensy flash (addresses below the first 512 bytes, that is not used by the drone firmware).
Reload drone control firmware
Go back to the drone_ctrl directory and reload
cd mobotware/drone_ctrl/trunk/drone_ctrl make make upload
The new compas calibration should be in effect.
