MMR

This page holds information relevant for the Natty Bumpo robot.

make video from images

1. Convert to filenames with sequential numbers and a supported image formap (e.g. png)

2. run ffmpeg with appropriate options

A script to do so could be:

#! /bin/bash
let COUNTER=1000000
for f in $( ls *.bmp ); do 
  echo convert $f path$COUNTER.png
  convert $f path$COUNTER.png
  let PREV=$COUNTER
  let COUNTER+=1
  done
# convert to mpeg format
# -r 25 frames per second
# -b 5000000 bitrate på 5Mbit/sec
# -y betyder overskriv destination
ffmpeg -y -r 25 -b 5000000 -i path1%06d.png path.mpeg
ls -l path.mpeg

---

Natty Bumpo – demo instructions (full version)

• updated august 2009 / jca
• to demonstrate sensor capabilities (no autonomous drive - sorry)

Using TOSHIBA PC for control (boot with linux).

Login as jca/******

Connect network cable to MMR (yellow crossed net cable)

Set IP adress (as root)

root$ ifconfig eth0 10.0.2.100

Start a console, and create 4 tabs (name the tabs: laser, cam, mrc, client)

• laser

jca$ ssh demo@smr16    (the usual demo password)
demo$ cd bin
demo$ ulmsserver

• cam

jca$ ssh demo@smr16    (the usual demo password)
demo$ cd bin
demo$ ucamserver

• mrc

jca$ ssh demo@smr16    (the usual demo password)
demo$ mrc -t1

• client

jca$ cd replay/mmrlive
jca$ auclient

This should show camera images and a laser scanner view - in a demonstration mode

If the remote control is on and set to "comp" (top-left switch "up), and NØDSTOP is down, then the laser scanner display and coordinate system will follow movement of the MMR (push MMR to demonstrate)

• see

>> disp help

for display options

---

FAQ

Tilt of laser scanner does not work.

The tilt controller can enter a no-operation mode where it needs a reset to resume operation. Reset can be done through the 'smrd' interface or by hardware action:

Hardware reset of laser scanner tilt controller:

Open plastic box behind the laser scanner (4 screws). The PCB closest to the laser scanner is the tilt controller board. The 2-wire (thick gray and orange wires) is the 24 volt supply, unplug this and reinsert. The tilt function should then find the lower extreme and reset to horizontal position.

If the tilt has passed one of the end-switches, the above reset might fail. In this case disconnect the two wires to the motor (red and black (red closest to scanner)) - screwed to the end of the controller board - and connect an external power supply (+/- 2 to 5 volt) to turn the tilt to a normal angle, then try the reset procedure again.

NB! Do not try to turn the laser scanner by hand - it will damage the axle.

Module will not load -- symbol not found

If the server is not compiled with the same library as the module, there may be "symbol not found" errors. The solution is to recompile their server with the same library as the modules (or vise versa).

---

Robot documentation

Documentation by Malte and Anders is on kalman:/vhome/ ... ?

hardware

1.2 GHz Via C2 processor with 512 MByte RAM.

---

Serial IO

The following devices are used:

/dev/ttyUSB0  // Laser scanner using USB/serial device
/dev/ttyS4    // symbolic link for old laser scanner server
/dev/ttyUSB1  // gps receiver
/dev/ttyACM0  // Small laser scanner (URG)
/dev/ttyS1    // used by smrd for RS485 interface

With kernel version 2.6.17, these are not the devices created by UDEV, they are now all in /dev/tts/*.

The com1 and com2 ports are swapped relative to ordinary SMRs, to correct for this the devices in the mmr are cross-linked in /etc/rc.d/rc.local as follows:

rm /dev/ttyS0
rm /dev/ttyS1
ln -s /dev/tts/1 /dev/ttyS0
ln -s /dev/tts/0 /dev/ttyS1

Further the devices /dev/tts/USB0 and /dev/tts/USB1 may be swapped after a reboot, to solve for this issue the devices are mapped to /dev/ttyUSB0 for gps and /dev/ttyUSB1 for SICK This is done in /etc/rc.d/rc.local using:

 if udevinfo -a -p /class/tty/ttyUSB0 | grep 'DRIVER=="pl2303"'; then
   echo USB0 is GPS, USB1 is SICK
   # direct ttyUSB0 to tts/USB0 as it is the gps connection
   ln -s /dev/tts/USB0 /dev/ttyUSB0
   # direct ttyS4 to tts/USB1 as it is the SICK laserscanner
   ln -s /dev/tts/USB1 /dev/ttyS4
   ln -s /dev/tts/USB1 /dev/ttyUSB1
 else
   echo USB0 is SICK, USB1 is GPS
   # direct ttyUSB0 to tts/USB1 as it is the gps connection
   ln -s /dev/tts/USB1 /dev/ttyUSB0
   # direct ttyS4 and ttyUSB1 to tts/USB0 as it is the SICK laserscanner
   ln -s /dev/tts/USB0 /dev/ttyS4
   ln -s /dev/tts/USB0 /dev/ttyUSB1
 fi

---

RAM disk

A RAM disk is mounted at

/mnt/ram

with write access for all. Remember all content are lost after a reboot. The RAM-disk takes RAM as needed up to a maximum of 300 MByte.

The ram disk size is defined in with the other disk definitions

/etc/fstab

with the line

tmpfs /mnt/ram tmpfs size=300m 0 0

The ram-disk is intended for temporary data (logging), that can be used in areas, where no network connection is available or as a fast logging device. These data can then later be copied to a more permanent place - if needed.

---

Flash disk

An user area is created on the flash disk for more permanent files at

/rhome

Please make a home directory using your initials or project number. e.g. like:

/rhome/ex39

There is limited space on the flash disk - p.t. approx 150 MByte. (Check disk space with the 'df' command).

---