Regbot: Difference between revisions

From Rsewiki
No edit summary
 
(140 intermediate revisions by 2 users not shown)
Line 1: Line 1:
Small robot intended for control-1 exercises.


[[File:regbot-final.png|200px]]
REGBOT is a small robot designed for exercises for our linear control 1 course (PID control) ([http://www.dtu.dk/english/Service/Phonebook/Person?id=14453 author]).


==Hardware==
[[file:foto_of_Alba_40.png | 250px]]


[[Design overview]] can be found here.
Figur 1. Version 2 of Regbot.


REGBOT comes in 2 versions:
== Overview ==
* version 1A - with robot number 1..15
* version 2B - with robot number 16..36


[[REGBOT robot status]]
This section is intended for users.


==Use software as is==
[[Getting started]] with REGBOT GUI.


To use regbot two software parts are needed - the one on the robot (regbot.hex) and the client (regbot.exe (for windows)).
[[User interface]], how to configure the robot using the Regbot client.


===Client software===
[[Control]] overview gives some information on control possibilities.


Get the client software (regbot.exe) from file sharing on campusnet, place it in a directory, this directory will be default for configuration file and result files from the robot.
[[Mission]], how to write a mission.


A USB driver must be installed to get in contact with the robot - see [[installation in windows]]
[[Regbot calibration]] for better performance.


The driver will (on Windows) create a com-port when connected - most likely com3 or any higher number.
[[Regbot maintenance]] for longer life.
When the robot is disconnected by unplugging the cable, then the client probably needs to be restarted if it was connected when the cable was unplugged (no connection detect in windows).


The run the regbot.exe file
[[Regbot GUI]] installation.


==Software download==
[[Regbot hardware board]].


*Robot software (regbot.hex): 2.241
== Install notes ==


*Client software for windows (regbot.exe): 2.247
This section is primarily installation notes and more detailed descriptions not usually needed by the end-user.


(as of 1 January 2016)
[[Regbot command interface]] - command list.


repository for software - client and robot
[[Software installation]] on REGBOT (Arduino) and tool-chain - Linux


* client: svn://repos.gbar.dtu.dk/jcan/regbot/qtgui
[[Regbot old stuff]]
* robot:  svn://repos.gbar.dtu.dk/jcan/regbot/regbot
 
On a Linux computer do something like this:
svn co svn://repos.gbar.dtu.dk/jcan/regbot/regbot .
svn co svn://repos.gbar.dtu.dk/jcan/regbot/qtgui .
 
==Install software tools==
 
The software tools to modify the software requires some tools.
 
* [[Software installation]] and tool-chain - Linux
* [[installation in windows]] and some of the tool-chain
* [[Schematic]]
 
==User interface (Client)==
 
The user interface can configure and run the robot, as well as inspecting almost all values on the robot. Written in python using Qt GUI library.
 
[[User interface]]

Latest revision as of 14:17, 17 October 2024

REGBOT is a small robot designed for exercises for our linear control 1 course (PID control) (author).

Figur 1. Version 2 of Regbot.

Overview

This section is intended for users.

Getting started with REGBOT GUI.

User interface, how to configure the robot using the Regbot client.

Control overview gives some information on control possibilities.

Mission, how to write a mission.

Regbot calibration for better performance.

Regbot maintenance for longer life.

Regbot GUI installation.

Regbot hardware board.

Install notes

This section is primarily installation notes and more detailed descriptions not usually needed by the end-user.

Regbot command interface - command list.

Software installation on REGBOT (Arduino) and tool-chain - Linux

Regbot old stuff