Install on raspberry

From Rsewiki
Revision as of 10:14, 23 December 2020 by Jca (talk | contribs) (→‎Prerequisite)

Short note on installation of (parts of) mobotware on Raspberry Pi (or Beagle-bone)


Prerequisite

  • Raspberry pi - version 3 or 4
  • SD-card preferably at least 16Gb
  • Monitor with HDMI (version 3) or micro HDMI (version 4) cable
  • Access to network (wired or wifi)
  • Power - either an USB charger or cable to a PC (micro USB (version 3) or USB-C (version 4)

Make SD card a FAT32 partision, if reusing an old card

A new SD-card is fine as is, else

see http://qdosmsq.dunbar-it.co.uk/blog/2013/06/noobs-for-raspberry-pi/ for instruction to prepare any old or new SD-card

add boot-files to SD card

Get the install zip-file from https://www.raspberrypi.org/downloads/noobs/

Then unpack NOOBS zip-file to the new disk (use the newest version), like for the network version 

unzip NOOBS_lite_v3_5_1.zip -d /media/xxx/yyyy  or
unzip ~/Downloads/raspberry/NOOBS_lite_v3_5_1.zip  (if you are on the empty flash)

or for the full version 

unzip NOOBS_v3_5_1.zip -d /media/xxx/yyyy  or
unzip ~/Downloads/raspberry/NOOBS_v3_5_1.zip  (if you are on the empty flash)

Reboot

That is all, Raspberry should boot on that.

or see instructions on e.g.: https://www.raspberrypi.org/help/noobs-setup/

Boot the raspberry and install the DEBIAN Linux.

Assuming DEBIAN is up and running - with internet access:

Configure

Raspberry

use raspi-config, start a terminal: 

sudo raspi-config

Using raspi-config 

Expand Filesystem (if not OK already)
Set keyboard layout
Enable Camera
Set hostname
Enable SSH
Enable i2c - load module as default
Disable Serial login
boot as a console with login
Update firmware
Set locale to "en_DK.UTF-8 UTF-8" (danish keyboard, but english language)

Beagle bone

login as root (no password)

After installing a boot-image on a microsd-card with debian, follow the instaructions to expand the boot image to use the full sd-card, as described in: http://elinux.org/Beagleboard:Expanding_File_System_Partition_On_A_microSD

Update operating system

Ensure you have internet access, then 

sudo apt-get update
sudo apt-get dist-upgrade
sudo reboot

Login

login as pi, password raspberry - password may have changed

or on beaglebone as root (no password)

add a user called local 

sudo adduser local
sudo usermod -a --groups adm,cdrom,sudo,audio,video,plugdev,games,users,netdev,input,spi,gpio,i2c,dialout local

switch user to local, and ensure groups are OK, and network is running 

su - local
groups
ifconfig

Note the inet address.

Now it is possible to login (as local) from network.

Get access using hostname

You may change the hostname by changing the name in /etc/hostname. If you do so, then you should probably restart before the new hostname works.

Now from another PC on the local network 

ping hostname.local

where "hostname" is replaced with the hostname in /etc/hostname.

Get filesystem on normal Linux PC

From another (Linux) PC, mount the raspberry filesystem 

mkdir rpi  (where the filesystem will be mounted)
sshfs local@10.59.8.141: rpi    (replace IP number with inet address from above, or use sshfs local@hostnale.local: rpi)

Then in directory rpi the user files on the raspberry can be manipulated.

for other access, use (with IP address as found above, or IP replaced with hostname.local) 

ssh -X local@10.59.8.141

Packages needed

sudo apt install cmake
sudo apt install libavcodec-dev libavformat-dev libswscale-dev libv4l-dev libxvidcore-dev libx264-dev libgtk2.0-dev 
sudo apt install libatlas-base-dev gfortran alsa-tools jackd1
sudo apt install libgstreamer1.0-dev libgstreamer-plugins-base1.0-dev subversion libreadline-dev htpdate aptitude
# video for linux had some error, maybe this will help
cd /usr/include/linux
sudo ln -s -f ../libv4l1-videodev.h videodev.h
# opencv
# sudo apt install libopencv-dev (sorry, installs opencv 2.4 (jan 2020), with no ArUco code support)

NB! Stop here if you install ROBOBOT

Opencv

As of June 2019 opencv 3.2 is installed using line above - NO, it is back to 2.4 on noops 3.2.1 (jan 2020/jca)

Newer version of Opencv could be installed manually if you really need functions not available in 3.2. For newer installation use 

# make a directory for the opencv source
cd
mkdir -p git
cd git
# get source
wget -O opencv-3.4.zip https://github.com/Itseez/opencv/archive/3.4.zip
unzip opencv-3.4.zip
wget -O opencv_contrib-3.4.zip https://github.com/Itseez/opencv_contrib/archive/3.4.zip
unzip opencv_contrib-3.4.zip
# you will need this - if you use python - takes some minutes
pip install numpy
# prepare compilation
cd ~/git/opencv-3.4/
mkdir build
cd build
cmake -D CMAKE_BUILD_TYPE=RELEASE \
   -D CMAKE_INSTALL_PREFIX=/usr/local \
   -D INSTALL_PYTHON_EXAMPLES=ON \
   -D OPENCV_EXTRA_MODULES_PATH=~/git/opencv_contrib-3.4/modules \
   -D BUILD_EXAMPLES=ON ..
# inspect printout to see if needed features are enabled
# use -j2 option not to overload or overheat the processor (j2 means use 2 cores only)
# this probably takes an hour or so
make -j2
# install into /usr/local
sudo make install
# load environment settings
sudo ldconfig

Packages needed for Mobotware RHD/MRC

Package list for RHD and MRC (paste the last line to a terminal window): 

libexpat-dev   (RHD)
pciutils-dev   (RHD)
libncurses-dev (RHD)
bison          (MRC)
libsdl-dev     (MRC)
telnet         (MRC test)
sshfs          (may be a good idea to access filesystem from another PC)
sudo apt-get install subversion libexpat-dev pciutils-dev libncurses-dev bison libsdl-dev telnet sshfs

Additional for AURS (e.g. camera server)

Package list - opencv removed as newer version installed above (paste the last line to a terminal window) 

cmake
# libopencv-dev
libreadline-dev
libudev-dev
libusb-dev
# libv4l-dev
python-dev
libgstreamer0.10-dev
libboost-dev
libboost-system-dev
python-opencv          (not needed, but nice)
sudo apt-get install cmake libreadline-dev libudev-dev libusb-dev libgstreamer0.10-dev libboost-dev libboost-system-dev python-opencv

Python

Further python image processing install 

sudo pip install Image

Mount filesystem

As an option, mount the home directory on raspberry-pi to your local PC for easy file modification.

On your PC type make a directory for the filesystem 

mkdir rpi
sshfs local@10.59.8.141: rpi
ls rpi

with your IP address or IP replaced by hostname.local.

Unmount with 

fusermount -u rpi

Mobotware

Get and unpack mobotware - see main page of this wiki for info

Either from SVN - if you have access, or from our lab-computers as a mobotware-XXX.tar.gz file, where XXX is version number.

unpack if a .gz file and make a symbolic link to "mobotware" to make this guide work. 

tar -xzf mobotware-XXX.tar.gz
ln -s mobotware-XXX mobotware

or, if from SVN: 

svn co svn://repos.gbar.dtu.dk/jcan/mobotware mobotware

this makes a mobotware directory with all the files.

Modify makefiles

Not all parts of Mobotware runs on a raspberry, so some parts must be removed from the Makefiles:

Enter the mobotware directory 

cd mobotware-XXX

main Makefile

nano -w Makefile

Change this section 

APPSUBDIRS = aumat/trunk \
   aurobotservers/trunk/include \
   aurobotservers/trunk/libs \
   mapbase/trunk \
   rhd/trunk \
   mrc/trunk \
   hakoclient/trunk  \
   aurs-plugins/aumanager aurs-plugins/aumrcobst aurs-plugins/auplanner/trunk \
   aurs-plugins/auzoneobst \
   aurobotservers/trunk \
   simulator/trunk

delete the lines 

hakoclient/trunk  (GUI for HAKO tractor)
simulator/trunk   (simulator will not run on raspberry)

so that it looks like 

APPSUBDIRS = aumat/trunk \
   aurobotservers/trunk/include \
   aurobotservers/trunk/libs \
   mapbase/trunk \
   rhd/trunk \
   mrc/trunk \
   aurs-plugins/aumanager aurs-plugins/aumrcobst aurs-plugins/auplanner/trunk \
   aurs-plugins/auzoneobst \
   aurobotservers/trunk

Remember to remove the last back-slash

RHD plugins Makefile

cd rhd/trunk/plugins
nano -w Makefile

In this section 

PLUGINLIST := auserial gps crossbow fogyro hakocan smrdserial rflex \
             rs232linesensor powercube esm slugs usbiss sf9dof \
             joycontrol gdm8246 buspiratei2c buspiratead \
             herkulex saberandmagenc imu gps2\
             smrarm rhdlog hexakopter gbprofibus roboteq gpsSocket \
             fieldsteer fielddrive fieldfrontenc \
             dynamixel cruizcore simstage3

Remove 

gbprofibus
simstage3

server Plug-ins etc.

Some servers and plug-ins are excluded from raspberry pi (qclient, kinect and point-cloud related plug-ins) in the respective Makefiles.

Build

Build mobotware: 

cd ~/mobotwareXXX
make

This should now compile with warnings only

(augraphplan.h not found may appear, but try one more make, then it usually works @todo - find out why)

install

The easyest way to use Mobotware is then to install into /usr/local/smr.

This is done by 

sudo make install

There will be a few error messages related to the uncompileable modules: qclient, hakoclient, simserver and libstage, this is OK.

setup path

Add the mobotware bin-directory into default PATH in /etc/profile 

sudo nano -w /etc/profile

append the PATH line with :/usr/local/smr/bin two places, like: 

...
if [ "`id -u`" -eq 0 ]; then
  PATH="/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/local/smr/bin"
else
  PATH="/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/local/games:/usr/games:/usr/local/smr/bin"
fi
...

And add mobotware AURS library path into .bashrc 

nano -w ~/.bashrc

append a line like this 

export LD_LIBRARY_PATH="$LD_LIBRARY_PATH:/usr/local/smr/lib"

To make this work, you have to logout and login again.

Make a Mobotware test configuration

Logout and login to ensure that the PATH settings gets implemented

Make a directory to run from 

mkdir ~/live
cd ~/live

Copy a robot configuration file 

cp -r /usr/local/etc/mobotware/calib .

make a rhdconfig.xml file with this content (loads a joystick and log plugin only). Look in mobotware/build/config for specific versions for different robots. 

<?xml version="1.0" ?>
<rhd>
 <sheduler>
   <period value="12000"/>
   <type value="LXRT"/>
 </sheduler>
 <server>
   <port value="24902"/>
   <clients number="10" allwriters="1"/>
 </server>
 <plugins basepath="/usr/local/smr/lib/rhdplugin/">
   <joycontrol enable="true" 
                   lib="libjoycontrol.so.1" 
                   critical="false" 
                   safety="1">
     <joystick port="/dev/input/js0"/>
     <speed maxfwd="900" 
          maxturn="900"
          fastBut="5"
          slowFactor="0.3"/>
     <deadband max="767" min="-767"/>
     <control enable="true"/>
   </joycontrol>
   <rhdlog enable="true"
         lib="rhdlog.so.1"
         critical="false"
         interval="1"
         safety="2"
         debug="0">
   </rhdlog>
 </plugins>
</rhd>

Test Mobotware

RHD

Hardware abstraction layer (Robot Hardware Daemon)

Start RHD 

rhd

It should end saying "RHD is running"

(Stops with ctrl-C)

MRC

Mobile Robot Control.

While the RHD is running (in another terminal)

start the MRC 

cd ~/live
mrc

This should show a list of options

-press 5 to quit

Laser scanner server

Start laser scanner server 

ulmsserver

There will be some errors as there is no laserscanner ...

Press enter a few times to get a prompt ">>"

Type 

help

this should show a list of loaded plugins, like 

...
Available commands (from currently loaded modules):
- push q server help shelp module do BASH alive quit exit
- scanGet scanPush scanSet
- odoPose odoPosePush
- mapPose mapPosePush
- utmPose utmPosePush
- var varPush
- poly
- mapbase
- settable addline setinitpose setinitcov localizeMHF localize resetlocalizer outputdist odoposeupdate resample localizeUKF
...

Try e.g. 

scanget fake=3

this should show a lot of HEX numbers and a few more errors.

Press q to quit

Camera server

Copy the camera server configuration for raspberry camera (otherwise a default ucamserver.ini will be created without the raspberry plugins). 

cp ~/mobotware/build/config/raspberry/ucamserver.ini .

Start the camera server - and optionally load the camera plug-in. 

ucamserver

This should end with something like this 

Camera_server 2.1966 (May  1 2015 13:42:21 jca@oersted.dtu.dk)
- on port 24920
- type h for help, q for quit

If camera is available, then use 

poollist

to se if camera is running.

Pres q to quit

Code change

Every time you recompile any module, it is not implemented until you also run 

cd ~/mobotware
sudo make install

To implement newly compiled modules right away, change a symbolic link: 

cd /usr/local
sudo rm smr
sudo ln -s ~/mobotware/build smr
Retrieved from "https://rsewiki.electro.dtu.dk/index.php?title=Install_on_raspberry&oldid=5129"