|
|
| Line 14: |
Line 14: |
|
| |
|
| [[Flexbot_parts_list | Leg components, electric design, PCB, schematic and firmware]] - PCB layout and part numbers. | | [[Flexbot_parts_list | Leg components, electric design, PCB, schematic and firmware]] - PCB layout and part numbers. |
| | |
| | [[mavlink| MAVLink communication protocol ]] |
|
| |
|
| ====Other pages==== | | ====Other pages==== |
| Line 25: |
Line 27: |
| =Instructions= | | =Instructions= |
|
| |
|
| [[mavlink| MAVLink communication protocol ]]
| |
|
| |
|
| [[compile_teensy| Updating, compiling and uploading Teensy code from the NUC]] | | [[compile_teensy| Updating, compiling and uploading Teensy code from the NUC]] |
| Line 32: |
Line 33: |
|
| |
|
| [[Importing_models_from_OnShape| Importing model from OnShape ]] | | [[Importing_models_from_OnShape| Importing model from OnShape ]] |
|
| |
| =Current state of Flexbot=
| |
| This section presents a '''very''' short summary of the current state of Flexbot. When a new change (of relevance i.e. no minors) is made, please update this section by adding a new line on top of the existing.
| |
|
| |
| * 03/12 2017: One complete leg of Flexbot has been build. PCBs have been fabricated and mounted. Main PCB holds all I/O + Teensy, another distributes power and thirds are current sensing breakout boards. No design errors have been identified to this point. MAVLink have been implemented as communication protocol. A GUI have been designed to visualise data wirelessly from Flexbot and simple control means have been implemented to test all actuators on Flexbot.
| |
|
| |
| * 23/07 2017: The mechanics from wheel to knee is finished. Electronics including external sensors have been mounted. Software supports basic functionality for interfacing, control, test and logging of each actuator (wheel, heading, height) and sensor.
| |
|
| |
| =Software terminal interface=
| |
| '''This is deprecated and replaced with MAVLink + GUI as of 03/12-2017. However code still remains in source code - not active'''
| |
|
| |
| Each Teensy can be interfaced separately via USB communication. Simply plug in a USB cable, open a serial communication in Putty, Arduino or whatever you prefer and type
| |
| help
| |
| This should return a menu with all options for the connected device. This should include:
| |
| * Changing controller and reference parameters
| |
| * Starting and stopping
| |
| * Printout of sensor data (to be used for debugging)
| |
| * Adding and removing items for logging
| |
| * Logging features (start logging, log interval and retrieve log in a MATLAB compatible format)
| |
| * Save and load to and from EEPROM (holds logging parameters and controller setting)
| |
Introduction
This is the main page of Flexbot. Here you will find all information and instructions related to the Flexbot project. A very important resource of this project is the git-repository which holds all documents, drawings, schematics and software.
Figure 1. Nice model of a Flexbot leg. The green parts are the main joints, foot, knee and hip. The black tubes are 16mm carbon fibre tubes, at the ends there are black plastic blocks, that connects the tube to the joint axle. The aluminium colourized parts are actuators and the base frame of the robot. The layout of the main joints are slightly outdated.
Information
GIT repository, documents, drawings and software.
Leg main geometry.
Leg components, electric design, PCB, schematic and firmware - PCB layout and part numbers.
MAVLink communication protocol
Other pages
Mechanical design assembly order hints.
Old Software to do list - change request and to do (please amend when you note a problem / and delete when solved)
Project plan notes
Instructions
Updating, compiling and uploading Teensy code from the NUC
Flexbot Visualizer (GUI)
Importing model from OnShape
